Produktbeschreibung
Bucket elevator is mainly used in many trades such as grain,feed,coal,metallurge,cement factory etc.It can lift the material like graininess,dustlike,small block or oil cleaning.But TDTG type double barrel bucket elevator is not suitable for lifting the material that is over 60ºC, with big impurity, oil surface leaching or with corrosive.Its feature:
1.The side plate of bottom is movable,easy to maintain.
2.The tail wheel,head wheel and shaftis conneted with flat key,it is fixedness.
Struction and working principle:
This machine is composed of elevator top,machine barrel,elevator bottom,rubber belt (chains ) and bucket etc.Rubber belt is surrounding between head wheel and tail wheel, the buckets are fixed on the belt as a certain distance.The material fall into the elevator from inlet, after bucket excavating the material,up to move following belt, throw the material by passing the head wheel,and discharge the material from outlet. In order to clean bottom inside and bucket belt, elevator bottom installed plug board and spiral tension device.
1.Elevator top is composed of chain drive section head cap,discharge ,bearing housing, shaft and head wheel. There are 3 ways of power transmission for users to choose :
1)reducer through flexible coupling straight drive.
2)chain and sprocket drive.
3)V-belt pulley drive.
2.Elevator box is composed of angle steel and steel sheet.
3.Elevator bottom has inlet. there are discharge gate on both sides of bottom under- part. and with spiral tension to adjust bucket belt.
elevator bottom can be installed dust pipe after dismounting the cover.
4.There are 2 kinds of type: rubber belt and chain.two ends of rubber belt are connected with special belt bolts, buckets are fixed on rubber belt (chains) with bucket bolts,nuts and spring washer.
5.There are 2 types of buckets:deep type and shallow type.the deep type buckets are used for graininess material, the shallow type buckets are used for dustlike material.
Main Technical Parameters
.
external view
all kinds of bucket elevator photos
Project Case
/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| After-sales Service: | 12 Months |
|---|---|
| Warranty: | 12 Months |
| Structure: | Conveyor System |
| Material: | Kohlenstoffstahl |
| Material Feature: | Heat Resistant |
| Application: | Chemical Industry, Grain Transport, Mining Transport, Power Plant |
How do I Prevent Wear and Damage to Ladder Sprockets during Conveyor Operation?
Preventing wear and damage to ladder sprockets during conveyor operation is essential to ensure their longevity and maintain the overall efficiency of the conveyor system. Here are some preventive measures to follow:
- Proper Lubrication: Apply the appropriate lubricant to the ladder sprockets and the conveyor chain regularly. Lubrication reduces friction between the sprocket teeth and the chain links, minimizing wear and prolonging the sprocket’s life.
- Chain Tension: Maintain the correct tension in the conveyor chain. Proper tensioning prevents excessive stress on the ladder sprockets and chain links, reducing wear and preventing premature failure.
- Chain Alignment: Ensure the conveyor chain is correctly aligned with the ladder sprocket. Misalignment can cause uneven wear on the sprocket teeth and chain links, leading to accelerated wear and potential damage.
- Cleanliness: Keep the ladder sprockets and the surrounding area clean from debris, dirt, and contaminants. Foreign particles can cause chain jamming, accelerated wear, and affect sprocket performance.
- Regular Inspection: Conduct regular visual inspections of the ladder sprockets to check for signs of wear, damage, or deformation. Early detection of issues allows for timely maintenance and prevents further damage.
- Replace Worn Sprockets: Monitor the condition of the ladder sprocket teeth regularly. If the sprocket teeth show significant wear, chipping, or deformation, replace the sprocket promptly to prevent further damage to the conveyor chain.
- Inspect Chain Wear: Regularly inspect the conveyor chain for signs of wear, stretching, or elongation. A worn chain can accelerate sprocket wear, so replace the chain if it is beyond its recommended service life.
- Load Capacity: Ensure that the ladder sprockets are appropriately sized and rated for the load capacity of the conveyor system. Using sprockets that are too small or not designed for heavy-duty applications can lead to premature wear and failure.
- Follow Manufacturer’s Guidelines: Adhere to the ladder sprocket manufacturer’s maintenance recommendations and service intervals. Manufacturers may provide specific guidelines for lubrication, tensioning, and inspection to optimize sprocket performance and longevity.
By following these preventive measures, you can minimize wear and damage to ladder sprockets, prolong their service life, and maintain a reliable and efficient conveyor system. Regular maintenance and inspections are essential to identify and address any potential issues early on, preventing costly downtime and ensuring the smooth operation of your conveyor system.
Can Ladder Sprockets be Used in Food Processing and Packaging Conveyors?
Yes, ladder sprockets can be used in food processing and packaging conveyors, but specific considerations must be taken to ensure compliance with food safety regulations and the unique requirements of the industry:
- Material Selection: Choose ladder sprockets made from food-grade materials that meet FDA and other food safety standards. Stainless steel or certain high-strength engineering plastics are commonly used for food processing applications due to their corrosion resistance and ease of cleaning.
- Sanitary Design: Ensure that the ladder sprocket design allows for easy cleaning and sanitization. Smooth surfaces without crevices or tight spaces can prevent bacterial growth and facilitate thorough cleaning.
- Resistance to Contamination: Select ladder sprockets that can withstand the harsh cleaning agents and sanitizing chemicals used in the food industry without degradation or contamination of the food product.
- Hygienic Lubricants: Use food-grade lubricants approved for use in food processing environments to lubricate the ladder sprockets and conveyor chain. Avoid lubricants that may come into contact with the food product.
- Proper Sealing: Ensure that the sprocket bearings are effectively sealed to prevent the ingress of contaminants and maintain a clean conveyor environment.
- Hazard Analysis and Critical Control Points (HACCP): Implement HACCP principles to identify potential hazards in the food processing and packaging process and implement control measures to prevent contamination. Properly selected and maintained ladder sprockets play a part in the overall hazard control strategy.
- Regular Inspection and Maintenance: Establish a robust maintenance program to regularly inspect and clean ladder sprockets to prevent contamination risks and ensure reliable conveyor performance.
- Compliance with Regulations: Ensure that the ladder sprockets and the overall conveyor system comply with relevant food safety regulations and industry standards, such as those set by the FDA, USDA, and other food safety agencies.
Due to the stringent requirements of the food processing and packaging industry, ladder sprockets used in these applications often have specialized designs and materials to ensure food safety and hygiene. It’s essential to work with conveyor system experts and sprocket manufacturers who understand the specific needs of the food industry and can provide suitable solutions.
By using ladder sprockets designed and constructed with food safety in mind, food processing and packaging conveyors can efficiently and safely handle food products while complying with the industry’s stringent regulations and quality standards.
Wie wähle ich die richtige Größe und Teilung eines Leiterkettenrads für mein Fördersystem?
Die Wahl der richtigen Größe und Teilung eines Leiterkettenrads für Ihr Fördersystem ist entscheidend für einen einwandfreien Betrieb, eine effiziente Kraftübertragung und eine lange Lebensdauer der Anlage. Die folgenden Schritte helfen Ihnen bei der Auswahl:
- 1. Förderkettentyp bestimmen: Determine the type of conveyor chain used in your system. Different chain types have specific pitch measurements, and the ladder sprocket must match the chain’s pitch to ensure proper engagement.
- 2. Anzahl der Kettenradzähne bestimmen: Calculate the required number of teeth for the ladder sprocket based on the desired conveyor speed, driven shaft RPM, and the chain’s speed factor. The speed factor is typically provided by the chain manufacturer.
- 3. Berücksichtigen Sie den Kettenwicklungswinkel: Ensure that the sprocket size allows for sufficient chain wrap around the sprocket to prevent chain disengagement. The chain wrap angle should be within the manufacturer’s recommended range.
- 4. Förderbandbelastung beurteilen: Evaluate the conveyor system’s load and the maximum tension the chain will experience. The ladder sprocket’s material and design must be able to handle the load without deformation or failure.
- 5. Wellendurchmesser bestimmen: The ladder sprocket’s bore size (inner hole) should match the driven shaft’s diameter or use a taper-lock bushing or through-bore hub to adapt the sprocket to the shaft size.
- 6. Platzbeschränkungen berücksichtigen: Stellen Sie sicher, dass die gewählte Leiterkettenradgröße in den verfügbaren Platz im Fördersystem passt, ohne andere Komponenten zu beeinträchtigen.
- 7. Herstellerangaben konsultieren: Refer to the ladder sprocket manufacturer’s data and specifications to find the appropriate sprocket size and pitch options for your specific conveyor chain type.
- 8. Wählen Sie hochwertige Materialien: Wählen Sie ein Leiterkettenrad aus hochwertigen Materialien, das eine gute Verschleißfestigkeit und Langlebigkeit bietet, insbesondere für Anwendungen mit rauen Umgebungsbedingungen oder hohen Belastungen.
- 9. Holen Sie sich fachkundigen Rat ein: Wenn Sie sich bei der Auswahl unsicher sind, wenden Sie sich an Experten für Fördersysteme oder Kettenradhersteller, um Unterstützung bei der Wahl der richtigen Leiterkettenradgröße und -teilung zu erhalten.
Durch sorgfältige Berücksichtigung des Kettentyps, der Förderbelastung, der Zähnezahl des Kettenrads und anderer relevanter Faktoren können Sie die passende Größe und Teilung eines Leiterkettenrads auswählen, das eine optimale Leistung und zuverlässige Kraftübertragung in Ihrem Fördersystem gewährleistet.
editor by Dream 2024-05-10